Why does the flange drop during use of a timing pulley?

The function of the flange is to prevent production accidents caused by deviation and drop of the timing belt. Therefore, the flange drops mainly because it is squeezed off by the timing belt that has deviated for a long time. We recommend that the customer regularly check the condition of the timing belt of the equipment to avoid its deviation.

Why does the timing pulley has no threaded hole?

If you have requirements for fixing screws, we recommend that you choose a timing pulley with the shaft hole specification P (round hole + threaded hole) or N·C (keyway hole + threaded hole).

What should be done if there is jitter during use of a timing belt?

Readjust the tension of the timing pulley. Generally, the belt runs unstably due to excessive shaft spacing and insufficient tension.

Why cannot be the threaded hole of a MISUMI aluminum timing pulley locked tightly?

As the aluminum material is relatively soft, slippage may occur if the tightening force is too large during locking. We recommend that the customer stops tightening once an obstruction is felt.

How to fix a timing pulley when the shaft hole specification is H (round hole)?

Generally, H (round hole) can be used only after additional processing. If you need a product that can be directly fixed and used, please choose MISUMI P (round hole + threaded hole) or N (keyway hole + threaded hole) specifications.

What does the number in the timing pulley S2M, S3M, P2M, P3M, T5, T10, 2GT, 3GT, etc. mean?

It mainly represents the tooth pitch of the belt, that is, the distance between two adjacent teeth. They are also the tooth profile models in the timing belt industry.

How to choose a timing belt after selecting a timing pulley?

First, the series must be matched. For example, the timing belts of S2M, S3M, and S5M can only match the timing pulleys of S2M, S3M, and S5M. Then, select the timing belt with an width corresponding to the ones indicated in the timing pulley specifications. Finally, select the needed perimeter.

What does the number in the timing pulley S2M, S3M, P2M, P3M, T5, T10, 2GT, 3GT, etc. mean?

It mainly represents the tooth pitch of the belt, that is, the distance between two adjacent teeth. They are also the tooth profile models in the timing belt industry.

(!) Since support from Microsoft will end on January 14th, 2020, Windows 7 will be excluded from the recommended environment from December 15th, 2019 on this site. Vì lý do Microsoft kết thúc hỗ trợ cho Windows 7 vào ngày 14/01/2020, Windows 7 sẽ là hệ điều hành không được khuyến khích sử dụng với trang web này từ ngày 15/12/2019.

Tel: 0222-361-1555 Email: cs@misumi.com.vn 8:00 - 17:00 (Mon - Sat)

ものづくりの、明日を支える。MISUMI-VONA 生産材コマースものづくりの、明日を支える。MISUMI-VONA 生産材コマース

Webcode Seach | Series: #CODE

Keyword suggestionsTừ khóa gợi ý

Part number suggestionsGợi ý mã sản phẩm

Discontinued Products

Search by Category / Brand Tìm theo danh mục, nhãn hiệu

Search by Category Tìm theo danh mục

[Thông báo] Cập nhật địa chỉ kho tập kết hàng hóa tại khu vực miền Nam của MISUMI Việt Nam. Xem chi tiết.
[Announcement] Update on warehouse address in the Southern region of MISUIMI Vietnam. See more. 
[Cảnh Báo] Thủ Đoạn Lừa Đảo Từ Nhân Viên Giao Hàng – Yêu Cầu Trả Phí Ship. Xem chi tiết.
[Warning] Fraud Calling from Shipper - Asking to Pay Shipping Fee. See more.

How can we improve?

How can we improve?

Comments

Name (Optional)

E-mail Address (Optional)

Tel (Optional)

While we are not able to respond directly to comments submitted in this form, the information will be reviewed for future improvement.
Customer Privacy Policy

Thank you for your cooperation.

While we are not able to respond directly to comments submitted in this form, the information will be reviewed for future improvement.
Please use the inquiry form.

Customer Privacy Policy

ConfigureTạo

Part number has not been determine

(16 Part Numbers Available)

Configure Remaining SpecificationsĐịnh cấu hình các thông số còn lại

Part Number CompleteĐã hoàn thành

C-TTPA14T10150-A-NK10

Type Belt Width Used Number of Teeth Material Shaft Bore Dia. d Shaft Hole Shape Number of Teeth type Pulley Shape CAD Days to Ship

Specification/DimensionsĐặc điểm kỹ thuật / Kích thướcĐặc điểm kỹ thuật / Kích thước

Type
- Timing Pulleys
ClearTrống
Belt Width Used(mm)
15

20

25

30

40

50
ClearTrống
Number of Teeth(T)
14

16

18

20
ClearTrống
Material
- Aluminum
  - Aluminum Alloy
  - Ultra Super Duralmin Type Aluminum Alloy
ClearTrống
Shaft Bore Dia. d(mm)
10

14

15

16

18

20

22

25
ClearTrống
Shaft Hole Shape
- N
- NK
- P
ClearTrống
Number of Teeth
12

14

16

18

20
ClearTrống
type
- C-TTPA□□T10
ClearTrống
Pulley Shape
- Shape A
ClearTrống
CADCAD
- 2D
- 3D
ClearTrống

Days to ShipSố ngày giao hàng

Alltất cả các

Same day

8 Day(s) or Less
ClearTrống

Specify AlterationsChỉ định thay đổi

Timing Pulleys T10

Until 31/12/2024
Volume Discount

Check FAQ of this product (8 items)

Brand :

MiSUMi Economy

Part Number :

C-TTPA14T10150-A-NK10 SALE

C-TTPA16T10150-A-N14 SALE

C-TTPA16T10150-A-N15 SALE

C-TTPA16T10200-A-N16 SALE

C-TTPA16T10250-A-N20 SALE

C-TTPA18T10200-A-N18 SALE

C-TTPA18T10250-A-N16 SALE

C-TTPA18T10250-A-N20 SALE

C-TTPA18T10250-A-N22 SALE

C-TTPA18T10500-A-N14 SALE

C-TTPA20T10200-A-N14 SALE

C-TTPA20T10200-A-N15 SALE

C-TTPA20T10250-A-N15 SALE

C-TTPA20T10300-A-N20 SALE

C-TTPA20T10400-A-N20 SALE

C-TTPA20T10400-A-N25 SALE

C-TTPA14T10150-A-NK10

Order Qty :
Total Price :

---
Days to ship :

---

Select part number to Order Now/ Add to Cart

CAD Download

(i)
Caution

thận trọng

**RoHS Compliant is available for some part numbers.
Please contact with MISUMI for detail effective date.

Product Description

Timing Pulleys T10
Timing Pulleys are an economy item, The price is cheaper than the MISUMI standard product.They offer a wide variety of sizes to choose from.
[Feature]
● Belt Width Used (mm.) : 15, 20,25, 30, 40 and 50
● Applicable with Belt Type : T10
● Number of Teeth : 14, 16, 18 and 20
● Shaft Bore Diameter Minimum/Maximum (mm.) : 10 to 25
● Shaft Bore Specs. : Can select between Round Hole + Tap and New JIS keyway + Tap
● Material : Aluminum Alloy
● Surface treatment : Clear Anodized
[Application]
Timing pulleys are frequently utilized in systems that incorporate timing belts to regulate and govern the movement of the machinery.
See more ...

Economy T10 Timing Pulley

Timing pulleysAluminum pulleysPrecision mechanics

- Available in sizes with 14 to 20 teeth

- Constructed from lightweight and durable aluminum

- Clear anodized finish for improved corrosion resistance

- Pulley compatible with various belt widths

- Easy installation with chamfered threaded holes

MISUMI Standard

Cheaper Price

Product Variety

3D CAD
3D CAD Support

Product Overview

Usually, timing pulleys, timing idlers and timing belts are widely used to design mechanisms for transmitting rotational power generated by motors.
Driving and transmission are realized through the engagement between the teeth of timing pulleys, timing idlers and timing belts.

Dimensional Drawing

Standard Tooth Profile	■Pulley Shape Shape A	■Shaft hole specification P round hole+threaded hole	N New JIS Keyway Hole + Threaded Hole

The tooth groove size varies slightly with the number of teeth (Tooth pitch: 10.0 mm)	Detailed Dimensions of Keyway The positions of keyway and tooth are not fixed. The threaded hole of the pulley is located near 120° to avoid interference with the tooth top.

Material Pulley: Aluminum Alloy
Flange: Aluminum Alloy

Surface Treatment: Clear Anodized

Tapped Hole Size Table
(Shaft Bore Specs.: P·N)

dH7 Shaft Bore ID	2-M (Coarse Thread)
10~12	M4×3
13~17	M5×4
18~30	M6×5

Specification Table

Part Number			Pulley Shape	Shaft Bore Specs.P Hole Dia.d	P.D.	O.D.	F	E
Type	Number of Teeth	Applicable Belt
C－TTPA	18	T10200	A	20	57.3	55.45	61	45

Part Number			Pulley Shape	Shaft Bore Specs.N Hole Dia.d	P.D.	O.D.	F	E
Type	Number of Teeth	Applicable Belt
C－TTPA	12	T10200	A	15	38.2	36.35	40	27
	14	T10150		12·14·15·NK10	44.56	42.7	48	35
	16			14	50.93	49.05	58	40
				15
		T10200		16
		T10250		15·20	50.93	49.05	58	40
	18	T10200		14·18	57.3	55.45	61	45
		T10250		16·20·22·25
		T10500		14
	20	T10200		14·15·25	63.66	61.8	67	50
		T10250		15·16·20
		T10300		15·20
		T10400		20·25

Detailed specifications are available on the official website

Product Features

■Usage difference between economy series timing pulleys and MISUMI standard product / Example of customer use

	Economy series Timing Pulleys	MISUMI Existing Products
Example of Use
Precautions	Generally used in reciprocating and conveyance mechanisms that require medium positioning accuracy	Generally used in mechanisms that frequently rotate forwardly and reversely and have requirements on positioning accuracy and backlash.
Repetitive positioning accuracy (reference value)	Medium precision (±0.1)	High precision (±0.05)

■More Convenient On-site Assembly
·MISUMI Economy series timing pulley is chamfered at the shaft bore and threaded hole for easy installation, reducing assembly time by 27% compared to the timing pulley not chamfered.

MISUMI Timing Pulley Assembly Time

* The values above are averages of test data and may vary individually.

■Longer Timing Belt Life
·MISUMI Economy series timing pulley, with deburring treatment at the threaded hole, is not easy to wear the timing belt, and the price is cheap while increasing the lifetime of the timing belt.

Belt condition after the test of timing belt pulley without chamfer on the threaded hole:
there are obvious wear marks left by the pulley tooth threaded hole on the belt tooth surface.
Photo of Belt Wear

[Test conditions]
Belt series: S5M
Belt width: 150mm
Number of teeth of drive side pulley: 20
Number of teeth of driven side pulley: 60
Speed: 3000 rpm
Tension (N): 160N
Test time: 24 H

* Problems of generic products on the market

Example of Use

Example drawing of a workpiece reversal transfer mechanism designed using MISUMI timing pulley

■Mechanism name
Workpiece Reversal Transfer Mechanism

■ Mechanism function
The workpiece moving on the conveyor belt rotates 90 degrees and then transfers to the next process.
At this time, the clamping mechanism rotates 180 degrees and does not change the direction of the workpiece relative to the conveying direction at the same time during transfer.

■Role of the timing pulley
The transmission of the timing pulley and the timing belt changes the placement direction of the workpiece while transferring the workpiece. (Applicable to S specification and GT specification timing pulleys)

For details, please click Workpiece Reversal Transfer Mechanism.

Usage Method

Usage Method Example Drawing	Usage Method of Timing Wheel and Timing Belt
	①Driving The driven wheel is driven by the driving wheel for transmission
	②Linear driving Reciprocating motion is carried out through the self-end timing toothed belt.

Usage Method Example Drawing	Usage Method of Timing Wheel and Timing Belt
	③Conveyance Plates are conveyed by two timing toothed belts
	④Traction transmission Workpieces are clamped and transmitted by the belt

Timing Pulleys T10, suitable for MISUMI Standard Timing Belts and Economy Series Timing Belts.

Precautions

There may be no surface treatment in the shaft hole.

The positions of keyway and tooth are not fixed.

Application Industries

Semiconductor	Automotive	Smart Phones

Medical	Electronic & Electrical	Robotics

Part Number

Incomplete part number.
Please use left hand selections to complete a part number.Incomplete part number.
Please use left hand selections to complete a part number.

Loading...Tải…

: 30; 45; 60

Part Number
C-TTPA14T10150-A-NK10SALE
C-TTPA16T10150-A-N14SALE
C-TTPA16T10150-A-N15SALE
C-TTPA16T10200-A-N16SALE
C-TTPA16T10250-A-N20SALE
C-TTPA18T10200-A-N18SALE
C-TTPA18T10250-A-N16SALE
C-TTPA18T10250-A-N20SALE
C-TTPA18T10250-A-N22SALE
C-TTPA18T10500-A-N14SALE
C-TTPA20T10200-A-N14SALE
C-TTPA20T10200-A-N15SALE
C-TTPA20T10250-A-N15SALE
C-TTPA20T10300-A-N20SALE
C-TTPA20T10400-A-N20SALE
C-TTPA20T10400-A-N25SALE

Price	Minimum Order Qty.	Volume Discount	Days to ShipSố ngày giao hàng	Type	Belt Width Used (mm)	Number of Teeth (T)	Pulley Shape	Material	Timing Pulley / Idler	Shaft Bore Dia. d (mm)	Shaft Hole Shape	Number of Teeth
122,954 VND 104,511 VND	1 Piece(s)	Available	Same day	Timing Pulleys	15	14	Shape A	[Aluminum] Aluminum Alloy	Pulleys	10	NK	-
151,421 VND 136,279 VND	1 Piece(s)	Available	Same day	Timing Pulleys	15	16	Shape A	[Aluminum] Aluminum Alloy	Pulleys	14	N	-
151,415 VND 136,274 VND	1 Piece(s)	Available	Same day	Timing Pulleys	15	16	Shape A	[Aluminum] Aluminum Alloy	Pulleys	15	N	-
172,365 VND 146,510 VND	1 Piece(s)	Available	Same day	Timing Pulleys	20	16	Shape A	[Aluminum] Aluminum Alloy	Pulleys	16	N	-
172,030 VND 146,226 VND	1 Piece(s)	Available	Same day	Timing Pulleys	25	16	Shape A	[Aluminum] Aluminum Alloy	Pulleys	20	N	-
190,241 VND 161,705 VND	1 Piece(s)	Available	Same day	Timing Pulleys	20	18	Shape A	[Aluminum] Aluminum Alloy	Pulleys	18	N	-
190,053 VND 161,545 VND	1 Piece(s)	Available	Same day	Timing Pulleys	25	18	Shape A	[Aluminum] Aluminum Alloy	Pulleys	16	N	-
190,020 VND 161,517 VND	1 Piece(s)	Available	Same day	Timing Pulleys	25	18	Shape A	[Aluminum] Aluminum Alloy	Pulleys	20	N	-
190,000 VND 161,500 VND	1 Piece(s)	Available	Same day	Timing Pulleys	25	18	Shape A	[Aluminum] Aluminum Alloy	Pulleys	22	N	-
362,993 VND 326,694 VND	1 Piece(s)	Available	Same day	Timing Pulleys	50	18	Shape A	[Aluminum] Aluminum Alloy	Pulleys	14	N	-
196,559 VND 176,903 VND	1 Piece(s)	Available	Same day	Timing Pulleys	20	20	Shape A	[Aluminum] Aluminum Alloy	Pulleys	14	N	-
196,553 VND 176,898 VND	1 Piece(s)	Available	Same day	Timing Pulleys	20	20	Shape A	[Aluminum] Aluminum Alloy	Pulleys	15	N	-
197,210 VND 167,629 VND	1 Piece(s)	Available	Same day	Timing Pulleys	25	20	Shape A	[Aluminum] Aluminum Alloy	Pulleys	15	N	-
246,335 VND 221,702 VND	1 Piece(s)	Available	Same day	Timing Pulleys	30	20	Shape A	[Aluminum] Aluminum Alloy	Pulleys	20	N	-
328,661 VND 279,362 VND	1 Piece(s)	Available	Same day	Timing Pulleys	40	20	Shape A	[Aluminum] Aluminum Alloy	Pulleys	20	N	-
328,584 VND 279,296 VND	1 Piece(s)	Available	Same day	Timing Pulleys	40	20	Shape A	[Aluminum] Aluminum Alloy	Pulleys	25	N	-

Loading...Tải…

Basic InformationThông tin cơ bản

Belt Type	T10	Surface Treatment	Clear Anodize

The specifications and dimensions of some parts may not be fully covered. For exact details, refer toCác thông số kỹ thuật và kích thước của mã sản phẩm có thể không được bao phủ đầy đủ. Để biết chi tiết chính xác, hãy tham khảo manufacturer catalogsdanh mục nhà sản xuất ..

Frequently asked question (FAQ)FAQ

Question:Question: Why does the flange drop during use of a timing pulley?: Answer:Answer: The function of the flange is to prevent production accidents caused by deviation and drop of the timing belt. Therefore, the flange drops mainly because it is squeezed off by the timing belt that has deviated for a long time. We recommend that the customer regularly check the condition of the timing belt of the equipment to avoid its deviation.
Question:Question: Why does the timing pulley has no threaded hole?: Answer:Answer: If you have requirements for fixing screws, we recommend that you choose a timing pulley with the shaft hole specification P (round hole + threaded hole) or N·C (keyway hole + threaded hole).
Question:Question: What should be done if there is jitter during use of a timing belt?: Answer:Answer: Readjust the tension of the timing pulley. Generally, the belt runs unstably due to excessive shaft spacing and insufficient tension.
Question:Question: Why cannot be the threaded hole of a MISUMI aluminum timing pulley locked tightly?: Answer:Answer: As the aluminum material is relatively soft, slippage may occur if the tightening force is too large during locking. We recommend that the customer stops tightening once an obstruction is felt.
Question:Question: How to fix a timing pulley when the shaft hole specification is H (round hole)?: Answer:Answer: Generally, H (round hole) can be used only after additional processing. If you need a product that can be directly fixed and used, please choose MISUMI P (round hole + threaded hole) or N (keyway hole + threaded hole) specifications.
Question:Question: What does the number in the timing pulley S2M, S3M, P2M, P3M, T5, T10, 2GT, 3GT, etc. mean?: Answer:Answer: It mainly represents the tooth pitch of the belt, that is, the distance between two adjacent teeth. They are also the tooth profile models in the timing belt industry.
Question:Question: How to choose a timing belt after selecting a timing pulley?: Answer:Answer: First, the series must be matched. For example, the timing belts of S2M, S3M, and S5M can only match the timing pulleys of S2M, S3M, and S5M. Then, select the timing belt with an width corresponding to the ones indicated in the timing pulley specifications. Finally, select the needed perimeter.
Question:Question: What does the number in the timing pulley S2M, S3M, P2M, P3M, T5, T10, 2GT, 3GT, etc. mean?: Answer:Answer: It mainly represents the tooth pitch of the belt, that is, the distance between two adjacent teeth. They are also the tooth profile models in the timing belt industry.

Check other FAQ (5 items) HideĐóng.

Top of the page

About MISUMIVề Misumi

About this WebsiteVề trang Web này

Useful ToolsCác công cụ hữu ích

Customer ServiceDịch vụ chăm sóc khách hàng

MISUMI Contact Monday to Saturday: 8:00 am - 5:00 pm Order cut off time is 5:00 pm Thứ 2 đến Thứ 7: 8 giờ sáng đến 5 giờ chiều Hạn chót đặt hàng là 5 giờ chiều

Tel:Số điện thoại:0222-361-1555
Fax:Số Fax:0222-361-2555
InquiryYêu cầu

MISUMI APP

Install MISUMI APP

MISUMI Vietnam Company Limited, Legal Representative: Tomohiro Watanabe,
phone: 0222-361-1555, e-mail: cs@misumi.com.vn, Enterprise Code: 0107514576,
Date of Issuance: 22 July 2016, Place of Issuance: Bac Ninh, Business Certificate No. 6573041568-KD dated 27 September 2016 issued by the People's Committee of Bac Ninh

Công ty TNHH MISUMI Việt Nam, Đại diện theo pháp luật: Tomohiro Watanabe,
Điện thoại: 0222-361-1555, e-mail: cs@misumi.com.vn, Mã số doanh nghiệp: 0107514576,
ngày cấp 22/7/2016, nơi cấp: Bắc Ninh, Giấy phép kinh doanh số: 6573041568-KD ngày cấp 27/9/2016 bởi UBND tỉnh Bắc Ninh

Flat-belt idlers, Width (T), 6 to 32 mm	Flat Belts For General Use	High Torque Timing Pulleys S2M Type

Representative model: HBG15-6	Representative model: HBLT350-4.23	Representative model: HTPA48S2M040-B-N10
Advantages: short delivery time, multiple types	Advantage: custom size	Advantages: short delivery time, multiple types

Search by Category / Brand Tìm theo danh mục, nhãn hiệu

Search by Category Tìm theo danh mục

How can we improve?

ConfigureTạo

Specification/DimensionsĐặc điểm kỹ thuật / Kích thướcĐặc điểm kỹ thuật / Kích thước

Type

Belt Width Used(mm)

Number of Teeth(T)

Material

Shaft Bore Dia. d(mm)

Shaft Hole Shape

Number of Teeth

type

Pulley Shape

CADCAD