Why is the order model of the timing belt inconsistent with the actual belt label and engraving?

Order model is MISUMI product model, the label on the belt or printed model on the belt surface is the belt manufacturer model, which varies with manufacturer, but there will be no influence on the product itself.

The timing belt has been broken after use for a very short period of time. Is there a problem with the quality of the belt?

The timing belt is a standard product, and the same batch of products have very few individual quality problems, please refer to Main causes of premature breakage and corresponding countermeasures to troubleshoot the equipment in use.

Can alteration be made to the timing belt?

Alteration cannot be made to the circumference of the timing belt, and partial alteration can be made to the width.

What kind of belt is better to use under conditions that require high cleanliness?

The use of urethane belts is recommended, which has significantly improved dust drop, compared to the rubber belt.

What are the two main types of timing belts according to their functions? What is the role?

Timing belts are mainly divided into transmission type and driving type. For transmission type, the load can be placed on the timing belt surface for transmission. For driving type, no load is carried, and only the role of transmitting torque is played, which is similar to the role of chain.

How to judge or measure whether the belt tension meets the installation requirements?

It is recommended that the customer purchase the tension meter by himself and make a judgment according to the calculation formula of the initial design.

Which tooth type of the timing belt has the smallest clearance? What will it affect?

The arc tooth type has minimum clearance, which can improve such indicators as positioning accuracy and rigidity.

(!) Since support from Microsoft will end on January 14th, 2020, Windows 7 will be excluded from the recommended environment from December 15th, 2019 on this site. Vì lý do Microsoft kết thúc hỗ trợ cho Windows 7 vào ngày 14/01/2020, Windows 7 sẽ là hệ điều hành không được khuyến khích sử dụng với trang web này từ ngày 15/12/2019.

Tel: 0222-361-1555 Email: cs@misumi.com.vn 8:00 - 17:00 (Mon - Sat)

ものづくりの、明日を支える。MISUMI-VONA 生産材コマースものづくりの、明日を支える。MISUMI-VONA 生産材コマース

Webcode Seach | Series: #CODE

Keyword suggestionsTừ khóa gợi ý

Part number suggestionsGợi ý mã sản phẩm

Discontinued Products

Search by Category / Brand Tìm theo danh mục, nhãn hiệu

Search by Category Tìm theo danh mục

[Thông báo] Cập nhật địa chỉ kho tập kết hàng hóa tại khu vực miền Nam của MISUMI Việt Nam. Xem chi tiết.
[Announcement] Update on warehouse address in the Southern region of MISUIMI Vietnam. See more. 
[Cảnh Báo] Thủ Đoạn Lừa Đảo Từ Nhân Viên Giao Hàng – Yêu Cầu Trả Phí Ship. Xem chi tiết.
[Warning] Fraud Calling from Shipper - Asking to Pay Shipping Fee. See more.

How can we improve?

How can we improve?

Comments

Name (Optional)

E-mail Address (Optional)

Tel (Optional)

While we are not able to respond directly to comments submitted in this form, the information will be reviewed for future improvement.
Customer Privacy Policy

Thank you for your cooperation.

While we are not able to respond directly to comments submitted in this form, the information will be reviewed for future improvement.
Please use the inquiry form.

Customer Privacy Policy

ConfigureTạo

Part number has not been determine

(524 Part Numbers Available)

Configure Remaining SpecificationsĐịnh cấu hình các thông số còn lại

Part Number CompleteĐã hoàn thành

C-HTBN218S2M-40

Belt Width (mm) Circumference Length Number of Teeth type CAD Days to Ship

Specification/DimensionsĐặc điểm kỹ thuật / Kích thướcĐặc điểm kỹ thuật / Kích thước

Belt Width (mm)(mm)
4

6

10
ClearTrống
Circumference Length(mm)
82

86

88

90

94

96

98

100

102

104

106

110

112

114

116

118

120

122

124

126

128

130

132

134

136

138

140

142

144

146

150

152

156

160

164

166

168

172

176

180

182

186

188

190

192

194

200

202

204

208

210

212

214

218

220

224

226

230

234

236

240

244

246

250

252

254

256

260

264

266

268

270

274

276

278

280

284

286

288

290

292

296

300

302

306

308

310

314

320

322

324

328

330

334

336

340

344

356

360

364

366

370

376

380

386

390

392

396

400

410

426

430

436

438

440

448

452

464

478

480

486

488

492

498

500

502

504

518

520

522

556

560

572

580

586

594

600

604

630

648

710

726

800

810

848

896

984

1016

1224

3000

3672

3828
ClearTrống
Number of Teeth
41

43

44

45

47

48

49

50

51

52

53

55

56

57

58

59

60

61

62

63

64

65

66

67

68

69

70

71

72

73

75

76

78

80

82

83

84

86

88

90

91

93

94

95

96

97

100

101

102

104

105

106

107

109

110

112

113

115

117

118

120

122

123

125

126

127

128

130

132

133

134

135

137

138

139

140

142

143

144

145

146

148

150

151

153

154

155

157

160

161

162

164

165

167

168

170

172

178

180

182

183

185

188

190

193

195

196

198

200

205

213

214

218

219

220

224

226

232

239

240

243

244

246

249

250

251

252

259

260

261

278

280

286

290

293

297

300

302

315

324

355

363

400

405

424

448

492

508

612

1500

1836

1914
ClearTrống
type
- C-HTBN□□S2M
ClearTrống
CADCAD
- 2D
- 3D
ClearTrống

Days to ShipSố ngày giao hàng

Alltất cả các

Same day

6 Day(s) or Less

8 Day(s) or Less

10 Day(s) or Less

12 Day(s) or Less

13 Day(s) or Less

14 Day(s) or Less
ClearTrống

Specify AlterationsChỉ định thay đổi

Timing Belts S2M (Part Number)

Until 31/12/2024
Volume Discount

Check FAQ of this product (7 items)

Brand :

MiSUMi Economy

Part Number :

C-HTBN218S2M-40 SALE

C-HTBN218S2M-60 SALE

C-HTBN218S2M-100 SALE

C-HTBN220S2M-40 SALE

C-HTBN220S2M-60 SALE

C-HTBN220S2M-100 SALE

C-HTBN224S2M-40 SALE

C-HTBN224S2M-60 SALE

C-HTBN224S2M-100 SALE

C-HTBN226S2M-40 SALE

C-HTBN226S2M-60 SALE

C-HTBN226S2M-100 SALE

C-HTBN230S2M-40 SALE

C-HTBN230S2M-60 SALE

C-HTBN230S2M-100 SALE

C-HTBN234S2M-40 SALE

C-HTBN234S2M-60 SALE

C-HTBN234S2M-100 SALE

C-HTBN236S2M-40 SALE

C-HTBN236S2M-60 SALE

C-HTBN218S2M-40

Order Qty :
Total Price :

---
Days to ship :

---

Select part number to Order Now/ Add to Cart

CAD Download

(i)
Caution

thận trọng

**RoHS Compliant is available for some part numbers.
Please contact with MISUMI for detail effective date.

Product Description

This is an economy item, The price is cheaper than the MISUMI standard product.

Economy S2M Timing Belt

Overcome TorqueExtended LifespanCustomizable

- Overcome Torque Limitations: Designed to handle significantly higher torque compared to standard timing belts, our S2M belts provide the power you need without compromising performance.

- Durable Construction for Extended Lifespan: Built with high-quality chloroprene rubber and a reinforced glass fiber core.

- Quiet Operation for Improved Work Environment: Experience reduced noise levels with our S2M belts, creating a more comfortable and productive workspace.

- Timing belt with customizable dimensions

- Benefit from accurate tooth profiles and precise dimensions, ensuring smooth power transfer and minimizing energy loss.

MISUMI Standard

Cheaper Price

Product Variety

3D CAD
3D CAD Support

Product Overview

Usually, timing pulleys and timing belt are widely used to design mechanisms for transmitting rotational power generated by motors.
Driving and transmission are realized through the engagement between the teeth of timing pulleys and timing belts.

Dimensional Drawing

■ Material/Specification Table

Material
① Rear rubber	Chloroprene
② Tooth rubber	Chloroprene
③ Core wire	Glass Fiber
④ Backing cloth	Nylon canvas

Specifications Overview

Types	Tooth pitch	Ra	Lr	H	h	i	PLD	Unit weight g/m (Width: 10mm)
S2M	2	1.3	1.3	1.36	0.76	0.6	0.254	13.0 (11.0)

Timing belt circumference length is core wire length.

C-HTBN belt operating temperature range: -30 to 90 ℃.

The timing belt model engraved on the back of the product is the manufacturer model.

MISUMI makes no commitment to this product brand.

For the transmission capacity and calculation and design method of economy series timing belt, please refer to the national standard (GB) design manual.

Specification Table

■ Specification Table
Economic type Toothed timing belt S2M S3M S5M S8M S14M type Ordering example

■C-HTBN
■Type S2M (Tooth pitch: 2mm)

Part Number		Belt Nominal Width	Number of Teeth	Belt Circumference Length (mm)
Type	Belt Number	Belt Nominal Width	Number of Teeth	Belt Circumference Length (mm)
C-HTBN	82S2M	40 (4mm) 60 (6mm) 100 (10mm)	41	82
	86S2M		43	86
	88S2M		44	88
	90S2M		45	90
	94S2M		47	94
	96S2M		48	96
	98S2M		49	98
	100S2M		50	100
	102S2M		51	102
	104S2M		52	104
	106S2M		53	106
	110S2M		55	110
	112S2M		56	112
	114S2M		57	114
	116S2M		58	116
	118S2M		59	118
	120S2M		60	120
	122S2M		61	122
	124S2M		62	124
	126S2M		63	126
	128S2M		64	128
	130S2M		65	130
	132S2M		66	132
	134S2M		67	134
	136S2M		68	136
	138S2M		69	138
	140S2M		70	140
	142S2M		71	142
	144S2M		72	144
	146S2M		73	146
	148S2M		74	148
	150S2M		75	150
	152S2M		76	152
	156S2M		78	156
	158S2M		79	158
	160S2M		80	160
	164S2M		82	164
	166S2M		83	166
	168S2M		84	168
	172S2M		86	172
	176S2M		88	176
	178S2M		89	178
	180S2M		90	180
	182S2M		91	182
	184S2M		92	184
	186S2M		93	186
	188S2M		94	188
	190S2M		95	190
	192S2M		96	192
	194S2M		97	194
	200S2M		100	200
	202S2M		101	202
	204S2M		102	204
	206S2M		103	206
	208S2M		104	208
	210S2M		105	210
	212S2M		106	212
	214S2M		107	214
	218S2M		109	218
	220S2M		110	220
	224S2M		112	224
	226S2M		113	226
	230S2M		115	230
	234S2M		117	234
236S2M	118	236
240S2M	120	240
244S2M	122	244
246S2M	123	246
248S2M	124	248
250S2M	125	250
252S2M	126	252
254S2M	127	254
256S2M	128	256
260S2M	130	260
262S2M	131	262
264S2M	132	264
266S2M	133	266
268S2M	134	268
270S2M	135	270
274S2M	137	274
276S2M	138	276
278S2M	139	278
280S2M	140	280
284S2M	142	284
286S2M	143	286
288S2M	144	288
290S2M	145	290
292S2M	146	292
296S2M	148	296
298S2M	149	298
300S2M	150	300
302S2M	151	302
306S2M	153	306
308S2M	154	308
310S2M	155	310
312S2M	156	312
314S2M	157	314
316S2M	158	316
318S2M	159	318
320S2M	160	320
322S2M	161	322
324S2M	162	324
328S2M	164	328
330S2M	165	330
334S2M	167	334
336S2M	168	336
340S2M	170	340
344S2M	172	344
348S2M	174	348
352S2M	176	352
354S2M	177	354
356S2M	178	356
360S2M	180	360
364S2M	182	364
366S2M	183	366
370S2M	185	370
376S2M	188	376
380S2M	190	380
386S2M	193	386
390S2M	195	390
392S2M	196	392
396S2M	198	396
400S2M	200	400
410S2M	205	410
426S2M	213	426
430S2M	215	430
436S2M	218	436
438S2M	219	438
440S2M	220	440
446S2M	223	446
448S2M	224	448
452S2M	226	452
460S2M	230	460
464S2M	232	464
468S2M	234	468
478S2M	239	478
480S2M	240	480
486S2M	243	486
488S2M	244	488
492S2M	246	492
494S2M	247	494
498S2M	249	498
500S2M	250	500
502S2M	251	502
504S2M	252	504
508S2M	254	508
518S2M	259	518
520S2M	260	520
522S2M	261	522
530S2M	265	530
556S2M	278	556
560S2M	280	560
572S2M	286	572
580S2M	290	580
586S2M	293	586
594S2M	297	594
600S2M	300	600
604S2M	302	604
630S2M	315	630
648S2M	324	648
650S2M	325	650
656S2M	328	656
710S2M	355	710
726S2M	363	726
754S2M	377	754
800S2M	400	800
810S2M	405	810
848S2M	424	848
896S2M	448	896
900S2M	450	900
984S2M	492	984
1016S2M	508	1016
1224S2M	612	1224
3000S2M	1500	3000
3672S2M	1836	3672
3828S2M	1914	3828

Product Features

		■ S type circular tooth profile rubber timing belt (S2M/S3M/S5M/S8M/S14M) Feature 1: Reasonable semi-circular arc tooth profile design can provide higher torque to adapt to high load transmission. Feature 2: Reduce the noise generated by high-speed operation. Feature 3: Tooth peak changes under force, ensuring a longer life than conventional circular tooth profile teeth. Feature 4: Have certain conductivity Feature 5: timing belt Operating Temperature Range: -30 to 90℃.
		■ P type circular tooth profile rubber timing belt (P5M/P8M) Feature 1: Reasonable semi-circular arc tooth profile design can provide higher torque to adapt to high load transmission. Feature 2: Special concave tooth peak design, better reducing noise generated by high-speed operation. Feature 3: Tooth peak changes under force, ensuring greater accuracy than conventional circular tooth profile teeth. Feature 4: Have certain conductivity Feature 5: timing belt Operating Temperature Range: -25 to 80℃.
		■ Trapezoidal tooth profile rubber timing belt (MXL/XL/H/T5/T10) Feature 1: Suitable for light load transmission, standard torque driving. Feature 2: Tooth rubber uses chloroprene to protect core wire, providing excellent bending fatigue resistance, heat resistance, oil resistance Feature 3: timing belt Ideal choice of economical and maintenance-free alternative to traditional transmission method. Feature 4: Have certain conductivity Feature 5: timing belt Operating Temperature Range: -30 to 90℃ (MXL/XL/H) , 0 to 80℃ (T5/T10)

Example of Use

Usage Method Example Drawing	Instructions for use of timing wheel and timing belt
	① Driving (The driven wheel is driven by the driving wheel for transmission)
	② Transmission (Used for repeated motion with the object not rotating and high requirements on positioning accuracy)

Usage Method Example Drawing	Instructions for use of timing wheel and timing belt
	③ Conveyance (Plates are conveyed by two timing toothed belts)
	④ Traction transmission (Workpieces are clamped and transmitted by the belt)

Usage Method

■ Installation method for timing belt transmission
①	Turn off the power supply, remove the protective cover, loosen the motor assembly timing belt, move the motor so that the belt is loose enough. The belt can be removed without prying. Never try to pry the belt down.
②	Remove the old belt and check for abnormal wear. Excessive wear may mean that there are problems in the design or maintenance of the transmission device.
③	Choose the right timing belt to replace.
④	To clean the timing belt and pulley, wipe with a cloth dipped in a small amount of non-volatile liquid. Soaking in detergent or scrubbing the belt with detergent is not advisable. To remove grease, it is also undesirable to wipe with sandpaper or scratch with a sharp object. The belt must be kept dry before installation and use.
⑤	Check the pulley for abnormal wear or cracks. If the wear is excessive, the pulley must be replaced.
⑥	Check whether the pulley is linearly symmetrical. Linear symmetry of the pulley is essential for the operation of the timing belt, especially the timing belt transmission device. Asymmetry of the pulley is shown as follows:

⑦	Check the remaining transmission device components, such as bearings and bushings, for symmetry, durability, lubrication and other conditions.
⑧	Install a new timing belt on the pulley. Never pry or use too much force.
⑨	Tighten to narrow the center distance of the transmission device until the tension tester detects that the belt tension is appropriate. Turn the driving wheel several times with your hands. Re-test tension.
⑩	Tighten the assembly timing belt of the motor and correct the torque. Since any change in the center distance of the transmission device during operation will result in poor belt performance, it is important to ensure that all transmission components have been tightened.
⑪	Start the device and observe the timing belt performance to see if there is abnormal vibration, and listen carefully if there is abnormal noise. It is best to turn off the machine and check the conditions of the bearing and motor. If it feels too hot to the touch, the belt may be too tight, the bearing may be asymmetrical, or the lubrication may be incorrect.

Precautions

① Do not bend the timing belt by force.
It is strictly forbidden to bend the belt, which easily causes breakage

Do not use in direct contact with water, solvent, oil, acid, alkali, UV, ozone, etc.

③ Please timing belt avoid using or keeping at extreme high or low temperatures beyond the operating temperature range, or in humid environments.
④ During installation and maintenance, be sure to cut off the power supply and confirm that the machine is completely stopped before proceeding.
⑤ When there may be impurities, be sure to set the guard.

Application Industries

Food	Semiconductor	Smart phone

Automotive	Electronic & Electrical Appliances	Medical

Related Products

High Torque Timing Pulleys S2M Type	Flat Timing Belt	(Economy Series) Toothed Timing Belt MXL XL L H Type

Typical timing belt model: HTPA48S2M040-B-N10	Typical timing belt model: HBLT350-4.23	Typical timing belt model: C-TBN236MXL025

Part Number

Incomplete part number.
Please use left hand selections to complete a part number.Incomplete part number.
Please use left hand selections to complete a part number.

Loading...Tải…

: 30; 60; 90

Part Number
C-HTBN218S2M-40SALE
C-HTBN218S2M-60SALE
C-HTBN218S2M-100SALE
C-HTBN220S2M-40SALE
C-HTBN220S2M-60SALE
C-HTBN220S2M-100SALE
C-HTBN224S2M-40SALE
C-HTBN224S2M-60SALE
C-HTBN224S2M-100SALE
C-HTBN226S2M-40SALE
C-HTBN226S2M-60SALE
C-HTBN226S2M-100SALE
C-HTBN230S2M-40SALE
C-HTBN230S2M-60SALE
C-HTBN230S2M-100SALE
C-HTBN234S2M-40SALE
C-HTBN234S2M-60SALE
C-HTBN234S2M-100SALE
C-HTBN236S2M-40SALE
C-HTBN236S2M-60SALE
C-HTBN236S2M-100SALE
C-HTBN240S2M-40SALE
C-HTBN240S2M-60SALE
C-HTBN240S2M-100SALE
C-HTBN244S2M-40SALE
C-HTBN244S2M-60SALE
C-HTBN244S2M-100SALE
C-HTBN246S2M-40SALE
C-HTBN246S2M-60SALE
C-HTBN246S2M-100SALE
C-HTBN248S2M-40SALE
C-HTBN248S2M-60SALE
C-HTBN248S2M-100SALE
C-HTBN250S2M-40SALE
C-HTBN250S2M-60SALE
C-HTBN250S2M-100SALE
C-HTBN252S2M-40SALE
C-HTBN252S2M-60SALE
C-HTBN252S2M-100SALE
C-HTBN254S2M-40SALE
C-HTBN254S2M-60SALE
C-HTBN254S2M-100SALE
C-HTBN256S2M-40SALE
C-HTBN256S2M-60SALE
C-HTBN256S2M-100SALE
C-HTBN260S2M-40SALE
C-HTBN260S2M-60SALE
C-HTBN260S2M-100SALE
C-HTBN262S2M-40SALE
C-HTBN262S2M-60SALE
C-HTBN262S2M-100SALE
C-HTBN264S2M-40SALE
C-HTBN264S2M-60SALE
C-HTBN264S2M-100SALE
C-HTBN266S2M-40SALE
C-HTBN266S2M-60SALE
C-HTBN266S2M-100SALE
C-HTBN268S2M-40SALE
C-HTBN268S2M-60SALE
C-HTBN268S2M-100SALE
C-HTBN270S2M-40SALE
C-HTBN270S2M-60SALE
C-HTBN270S2M-100SALE
C-HTBN274S2M-40SALE
C-HTBN274S2M-60SALE
C-HTBN274S2M-100SALE
C-HTBN276S2M-40SALE
C-HTBN276S2M-60SALE
C-HTBN276S2M-100SALE
C-HTBN278S2M-40SALE
C-HTBN278S2M-60SALE
C-HTBN278S2M-100SALE
C-HTBN280S2M-40SALE
C-HTBN280S2M-60SALE
C-HTBN280S2M-100SALE
C-HTBN284S2M-40SALE
C-HTBN284S2M-60SALE
C-HTBN284S2M-100SALE
C-HTBN286S2M-40SALE
C-HTBN286S2M-60SALE
C-HTBN286S2M-100SALE
C-HTBN288S2M-40SALE
C-HTBN288S2M-60SALE
C-HTBN288S2M-100SALE
C-HTBN290S2M-40SALE
C-HTBN290S2M-60SALE
C-HTBN290S2M-100SALE
C-HTBN292S2M-40SALE
C-HTBN292S2M-60SALE
C-HTBN292S2M-100SALE

Price	Minimum Order Qty.	Volume Discount	Days to ShipSố ngày giao hàng	Belt Width (mm) (mm)	Circumference Length (mm)	Number of Teeth
15,458 VND 13,139 VND	4 Piece(s)	Available	13 Day(s)	4	218	109
15,459 VND 13,140 VND	4 Piece(s)	Available	13 Day(s)	6	218	109
15,838 VND 13,462 VND	4 Piece(s)	Available	13 Day(s)	10	218	109
15,618 VND 13,275 VND	4 Piece(s)	Available	14 Day(s)	4	220	110
15,628 VND 13,284 VND	4 Piece(s)	Available	14 Day(s)	6	220	110
17,336 VND 14,736 VND	1 Piece(s)	Available	Same day	10	220	110
15,618 VND 13,275 VND	4 Piece(s)	Available	14 Day(s)	4	224	112
15,628 VND 13,284 VND	4 Piece(s)	Available	14 Day(s)	6	224	112
17,568 VND 14,933 VND	4 Piece(s)	Available	14 Day(s)	10	224	112
15,459 VND 13,140 VND	4 Piece(s)	Available	13 Day(s)	4	226	113
15,459 VND 13,140 VND	4 Piece(s)	Available	13 Day(s)	6	226	113
16,218 VND 13,785 VND	4 Piece(s)	Available	13 Day(s)	10	226	113
15,618 VND 13,275 VND	4 Piece(s)	Available	14 Day(s)	4	230	115
15,629 VND 13,285 VND	4 Piece(s)	Available	14 Day(s)	6	230	115
17,878 VND 15,196 VND	4 Piece(s)	Available	14 Day(s)	10	230	115
25,502 VND 21,677 VND	4 Piece(s)	Available	8 Day(s)	4	234	117
25,515 VND 21,688 VND	1 Piece(s)	Available	Same day	6	234	117
25,540 VND 21,709 VND	4 Piece(s)	Available	8 Day(s)	10	234	117
15,619 VND 13,276 VND	4 Piece(s)	Available	14 Day(s)	4	236	118
15,630 VND 13,286 VND	4 Piece(s)	Available	14 Day(s)	6	236	118
18,260 VND 15,521 VND	4 Piece(s)	Available	14 Day(s)	10	236	118
25,206 VND 21,425 VND	4 Piece(s)	Available	10 Day(s)	4	240	120
25,208 VND 21,427 VND	1 Piece(s)	Available	Same day	6	240	120
25,211 VND 21,429 VND	1 Piece(s)	Available	Same day	10	240	120
15,620 VND 13,277 VND	4 Piece(s)	Available	14 Day(s)	4	244	122
15,631 VND 13,286 VND	4 Piece(s)	Available	14 Day(s)	6	244	122
18,647 VND 15,850 VND	4 Piece(s)	Available	14 Day(s)	10	244	122
15,620 VND 13,277 VND	4 Piece(s)	Available	14 Day(s)	4	246	123
15,631 VND 13,286 VND	4 Piece(s)	Available	14 Day(s)	6	246	123
18,803 VND 15,983 VND	1 Piece(s)	Available	Same day	10	246	123
20,010 VND 17,009 VND	1 Piece(s)	Available	13 Day(s)	4	-	-
20,012 VND 17,010 VND	1 Piece(s)	Available	13 Day(s)	6	-	-
20,013 VND 17,011 VND	1 Piece(s)	Available	13 Day(s)	10	-	-
15,621 VND 13,278 VND	4 Piece(s)	Available	14 Day(s)	4	250	125
15,632 VND 13,287 VND	1 Piece(s)	Available	Same day	6	250	125
19,032 VND 16,177 VND	4 Piece(s)	Available	14 Day(s)	10	250	125
15,459 VND 13,140 VND	4 Piece(s)	Available	13 Day(s)	4	252	126
15,460 VND 13,141 VND	4 Piece(s)	Available	13 Day(s)	6	252	126
17,511 VND 14,884 VND	4 Piece(s)	Available	13 Day(s)	10	252	126
15,459 VND 13,140 VND	4 Piece(s)	Available	13 Day(s)	4	254	127
15,460 VND 13,141 VND	4 Piece(s)	Available	13 Day(s)	6	254	127
17,588 VND 14,950 VND	4 Piece(s)	Available	13 Day(s)	10	254	127
15,621 VND 13,278 VND	4 Piece(s)	Available	14 Day(s)	4	256	128
15,632 VND 13,287 VND	1 Piece(s)	Available	Same day	6	256	128
19,341 VND 16,440 VND	4 Piece(s)	Available	14 Day(s)	10	256	128
25,206 VND 21,425 VND	4 Piece(s)	Available	10 Day(s)	4	260	130
25,208 VND 21,427 VND	1 Piece(s)	Available	Same day	6	260	130
25,211 VND 21,429 VND	1 Piece(s)	Available	Same day	10	260	130
20,010 VND 17,009 VND	1 Piece(s)	Available	13 Day(s)	4	-	-
20,012 VND 17,010 VND	1 Piece(s)	Available	13 Day(s)	6	-	-
20,014 VND 17,012 VND	1 Piece(s)	Available	13 Day(s)	10	-	-
15,459 VND 13,140 VND	4 Piece(s)	Available	13 Day(s)	4	264	132
15,460 VND 13,141 VND	4 Piece(s)	Available	13 Day(s)	6	264	132
18,120 VND 15,402 VND	4 Piece(s)	Available	13 Day(s)	10	264	132
15,622 VND 13,279 VND	4 Piece(s)	Available	14 Day(s)	4	266	133
15,634 VND 13,289 VND	1 Piece(s)	Available	Same day	6	266	133
19,881 VND 16,899 VND	4 Piece(s)	Available	14 Day(s)	10	266	133
15,459 VND 13,140 VND	4 Piece(s)	Available	13 Day(s)	4	268	134
15,460 VND 13,141 VND	4 Piece(s)	Available	13 Day(s)	6	268	134
18,274 VND 15,533 VND	4 Piece(s)	Available	13 Day(s)	10	268	134
15,459 VND 13,140 VND	4 Piece(s)	Available	13 Day(s)	4	270	135
15,460 VND 13,141 VND	4 Piece(s)	Available	13 Day(s)	6	270	135
18,425 VND 15,661 VND	4 Piece(s)	Available	13 Day(s)	10	270	135
15,459 VND 13,140 VND	4 Piece(s)	Available	13 Day(s)	4	274	137
15,460 VND 13,141 VND	4 Piece(s)	Available	13 Day(s)	6	274	137
18,577 VND 15,790 VND	4 Piece(s)	Available	13 Day(s)	10	274	137
15,459 VND 13,140 VND	4 Piece(s)	Available	13 Day(s)	4	276	138
15,460 VND 13,141 VND	4 Piece(s)	Available	13 Day(s)	6	276	138
18,731 VND 15,921 VND	4 Piece(s)	Available	13 Day(s)	10	276	138
15,459 VND 13,140 VND	4 Piece(s)	Available	13 Day(s)	4	278	139
15,460 VND 13,141 VND	4 Piece(s)	Available	13 Day(s)	6	278	139
18,807 VND 15,986 VND	4 Piece(s)	Available	13 Day(s)	10	278	139
15,623 VND 13,280 VND	4 Piece(s)	Available	14 Day(s)	4	280	140
15,636 VND 13,291 VND	1 Piece(s)	Available	Same day	6	280	140
20,729 VND 17,620 VND	4 Piece(s)	Available	14 Day(s)	10	280	140
15,459 VND 13,140 VND	4 Piece(s)	Available	13 Day(s)	4	284	142
15,460 VND 13,141 VND	4 Piece(s)	Available	13 Day(s)	6	284	142
19,109 VND 16,243 VND	4 Piece(s)	Available	13 Day(s)	10	284	142
25,208 VND 21,427 VND	1 Piece(s)	Available	Same day	4	286	143
25,208 VND 21,427 VND	1 Piece(s)	Available	Same day	6	286	143
25,214 VND 21,432 VND	1 Piece(s)	Available	Same day	10	286	143
25,208 VND 21,427 VND	4 Piece(s)	Available	10 Day(s)	4	288	144
25,208 VND 21,427 VND	4 Piece(s)	Available	10 Day(s)	6	288	144
25,214 VND 21,432 VND	4 Piece(s)	Available	10 Day(s)	10	288	144
15,624 VND 13,280 VND	1 Piece(s)	Available	Same day	4	290	145
15,637 VND 13,291 VND	4 Piece(s)	Available	14 Day(s)	6	290	145
21,269 VND 18,079 VND	4 Piece(s)	Available	14 Day(s)	10	290	145
15,459 VND 13,140 VND	4 Piece(s)	Available	13 Day(s)	4	292	146
15,460 VND 13,141 VND	4 Piece(s)	Available	13 Day(s)	6	292	146
19,489 VND 16,566 VND	4 Piece(s)	Available	13 Day(s)	10	292	146

Loading...Tải…

Basic InformationThông tin cơ bản

Belt Shape	Closed End	Belt Tooth Surface	Standard (Single Sided)	Belt Material	Rubber Belt
Core Wire Material	Glass Fiber	Belt Type	S2M	Belt Shape Type	Round Tooth Profile Super Torque
Transmission Torque	High Torque Transmission

The specifications and dimensions of some parts may not be fully covered. For exact details, refer toCác thông số kỹ thuật và kích thước của mã sản phẩm có thể không được bao phủ đầy đủ. Để biết chi tiết chính xác, hãy tham khảo manufacturer catalogsdanh mục nhà sản xuất ..

Frequently asked question (FAQ)FAQ

Question:Question: Why is the order model of the timing belt inconsistent with the actual belt label and engraving?: Answer:Answer: Order model is MISUMI product model, the label on the belt or printed model on the belt surface is the belt manufacturer model, which varies with manufacturer, but there will be no influence on the product itself.
Question:Question: The timing belt has been broken after use for a very short period of time. Is there a problem with the quality of the belt?: Answer:Answer: The timing belt is a standard product, and the same batch of products have very few individual quality problems, please refer to Main causes of premature breakage and corresponding countermeasures to troubleshoot the equipment in use.
Question:Question: Can alteration be made to the timing belt?: Answer:Answer: Alteration cannot be made to the circumference of the timing belt, and partial alteration can be made to the width.
Question:Question: What kind of belt is better to use under conditions that require high cleanliness?: Answer:Answer: The use of urethane belts is recommended, which has significantly improved dust drop, compared to the rubber belt.
Question:Question: What are the two main types of timing belts according to their functions? What is the role?: Answer:Answer: Timing belts are mainly divided into transmission type and driving type. For transmission type, the load can be placed on the timing belt surface for transmission. For driving type, no load is carried, and only the role of transmitting torque is played, which is similar to the role of chain.
Question:Question: How to judge or measure whether the belt tension meets the installation requirements?: Answer:Answer: It is recommended that the customer purchase the tension meter by himself and make a judgment according to the calculation formula of the initial design.
Question:Question: Which tooth type of the timing belt has the smallest clearance? What will it affect?: Answer:Answer: The arc tooth type has minimum clearance, which can improve such indicators as positioning accuracy and rigidity.

Check other FAQ (4 items) HideĐóng.

Top of the page

About MISUMIVề Misumi

About this WebsiteVề trang Web này

Useful ToolsCác công cụ hữu ích

Customer ServiceDịch vụ chăm sóc khách hàng

MISUMI Contact Monday to Saturday: 8:00 am - 5:00 pm Order cut off time is 5:00 pm Thứ 2 đến Thứ 7: 8 giờ sáng đến 5 giờ chiều Hạn chót đặt hàng là 5 giờ chiều

Tel:Số điện thoại:0222-361-1555
Fax:Số Fax:0222-361-2555
InquiryYêu cầu

MISUMI APP

Install MISUMI APP

MISUMI Vietnam Company Limited, Legal Representative: Tomohiro Watanabe,
phone: 0222-361-1555, e-mail: cs@misumi.com.vn, Enterprise Code: 0107514576,
Date of Issuance: 22 July 2016, Place of Issuance: Bac Ninh, Business Certificate No. 6573041568-KD dated 27 September 2016 issued by the People's Committee of Bac Ninh

Công ty TNHH MISUMI Việt Nam, Đại diện theo pháp luật: Tomohiro Watanabe,
Điện thoại: 0222-361-1555, e-mail: cs@misumi.com.vn, Mã số doanh nghiệp: 0107514576,
ngày cấp 22/7/2016, nơi cấp: Bắc Ninh, Giấy phép kinh doanh số: 6573041568-KD ngày cấp 27/9/2016 bởi UBND tỉnh Bắc Ninh