What brand is the linear bearing of FA?

The linear bearing of FA is MISUMI brand.

Is there a product stamp on the linear bearing?

There is no stamp on the product body, and the product model is on the packaging box.

How is linear bearing maintained regularly?

MISUMI recommends that linear bearing is regularly replenished with grease, and it is recommended to do so once every six months. When the moving distance is long, it is recommended to move once every three months or when the moving distance exceeds 1000km within the time limit, the 1000km shall prevail.

Comparison of antirust ability of linear bearings?

Antirust ability from strong to weak: No-Electro Nickel Plated → No Surface Treatment. Standard grade bearing steel is easy to rust, so it is necessary to apply anti-rust oil regularly.

What is the difference between the single liner type and the double liner type of linear bearing of FA?

Single liner type is one row of steel balls, and double liner type is two rows of steel balls. Generally, the length of the double liner type is more than twice that of the single liner type, and the contact area of steel balls is longer, the radial sway is smaller, and the rated load is larger.

When the linear bearing and the guide shaft are used together, some are closely matched, but some have relatively large clearance. Does it affect the use?

The linear bearing and the guide shaft are in point contact and rolling fit through the circulating steel ball structure. Because of point contact and non-interference fit, it is normal to have clearance between the shaft and the bearing, which will not affect the use. The use of this structure greatly reduces the friction resistance and prolongs the service life of the workpiece.

How to deal with oil leakage in the received linear bearing?

Linear bearing is coated with anti-rust oil (except for MX grease device) when leaving the factory, which has little influence on grease. It is recommended to clean it before use and apply grease after drying.

Can the linear bearing rotate?

The linear bearing is not suitable for rotating motion in structure. If it is forcibly rotated, it may cause damage to the product. If rotating motion is required, please give priority to linear type rotating bushings.

(!) Since support from Microsoft will end on January 14th, 2020, Windows 7 will be excluded from the recommended environment from December 15th, 2019 on this site. Vì lý do Microsoft kết thúc hỗ trợ cho Windows 7 vào ngày 14/01/2020, Windows 7 sẽ là hệ điều hành không được khuyến khích sử dụng với trang web này từ ngày 15/12/2019.

Tel: 0222-361-1555 Email: cs@misumi.com.vn 8:00 - 17:00 (Mon - Sat)

ものづくりの、明日を支える。MISUMI-VONA 生産材コマースものづくりの、明日を支える。MISUMI-VONA 生産材コマース

Webcode Seach | Series: #CODE

Keyword suggestionsTừ khóa gợi ý

Part number suggestionsGợi ý mã sản phẩm

Discontinued Products

Search by Category / Brand Tìm theo danh mục, nhãn hiệu

Search by Category Tìm theo danh mục

[Thông báo] Cập nhật địa chỉ kho tập kết hàng hóa tại khu vực miền Nam của MISUMI Việt Nam. Xem chi tiết.
[Announcement] Update on warehouse address in the Southern region of MISUIMI Vietnam. See more. 
[Cảnh Báo] Thủ Đoạn Lừa Đảo Từ Nhân Viên Giao Hàng – Yêu Cầu Trả Phí Ship. Xem chi tiết.
[Warning] Fraud Calling from Shipper - Asking to Pay Shipping Fee. See more.

How can we improve?

How can we improve?

Comments

Name (Optional)

E-mail Address (Optional)

Tel (Optional)

While we are not able to respond directly to comments submitted in this form, the information will be reviewed for future improvement.
Customer Privacy Policy

Thank you for your cooperation.

While we are not able to respond directly to comments submitted in this form, the information will be reviewed for future improvement.
Please use the inquiry form.

Customer Privacy Policy

ConfigureTạo

Part number has not been determine

(1 Part Numbers Available)

Configure Remaining SpecificationsĐịnh cấu hình các thông số còn lại

Part Number CompleteĐã hoàn thành

E-LBKM13LUU

Holder Material type Inscribed Circle Dia. dr Overall Length L Outer Cylinder Surface Treatment Outer Dia. D Ball Recirculating Type Length Eccentricity Style of Mounting Hole CAD Days to Ship

Specification/DimensionsĐặc điểm kỹ thuật / Kích thướcĐặc điểm kỹ thuật / Kích thước

Holder Material
- Opposite couterbored
- Standard
ClearTrống
type
- E-LBK
- E-LBKL
- E-LBKM
- E-LBKZ
ClearTrống
Inscribed Circle Dia. dr(Ø)
5

6

8

10

12

13

16

20

25

30

35

40

50
ClearTrống
Overall Length L(mm)
15

19

24

29

30

32

35

37

42

45

55

57

59

61

64

70

80

100

112

123

135

151

192
ClearTrống
Outer Cylinder Surface Treatment
- No Surface Treatment
- Surface Treatment
  - Electroless Nickel Plating
ClearTrống
Outer Dia. D(Ø)
10

12

15

19

21

23

28

32

40

45

52

60

80
ClearTrống
Ball Recirculating Type
- Single
- Double
ClearTrống
Length
- Single
- Double
ClearTrống
Eccentricity(µm)
0.02

0.024

0.03

0.04

0.045

0.28

24

30

40
ClearTrống
Style of Mounting Hole
- Opposite Couterbored Hole
- Standard Counterbored Hole
ClearTrống
CADCAD
- 2D
- 3D
ClearTrống

Days to ShipSố ngày giao hàng

Alltất cả các

Same day

8 Day(s) or Less
ClearTrống

Specify AlterationsChỉ định thay đổi

Square Flanged Linear Bushings, Single / Double / Opposite Counterbored Hole (E-LBKM13LUU)

Until 31/12/2024
Volume Discount

Check FAQ of this product (8 items)

Brand :

MiSUMi Economy

Order Qty :
Total Price :

---
Days to ship :

---

Select part number to Order Now/ Add to Cart

CAD Download

(i)
Caution

thận trọng

**RoHS Compliant is available for some part numbers.
Please contact with MISUMI for detail effective date.
Note: When ordering item E-LB**UU, you may receive product with package printed C-LM**UU. This is Misumi's product code convertion only, there is no spec difference between these 2 items

Product Description

Square Flanged Linear Bushings, Single / Double / Opposite Counterbored Hole
These Linear Bushings are an economy item, The price is cheaper than the MISUMI standard product.They offer a wide variety of sizes to choose from.
[Features]
● Support Shaft Diameter Minimum/Maximum (mm.): 6 and 50
● Overall Length Minimum/Maximum (mm.): 19 and 192
● Shape : Square Flanged
● Ball Recirculating Type : Single or Double
● Material:
- Housing - SUJ2 Equivalent
- Ball - SUJ2 Equivalent
[Application]
It is used in industrial machinery such as conveyor systems, packaging machines, and robotic equipment.
See more ...

Economy Square Flanged Linear Bushing

SquareRobustSupport

- Reliable square flanged bushing for robust support.

- Single and double ball recirculating types for various uses.

- High-quality SUJ2 equivalent material for long-lasting use.

- Supports a range of shaft diameters with precise tolerances

- Suitable for packaging machines and conveyor systems.

MISUMI Standard

Cheaper Price

Product Variety

3D CAD
3D CAD Support

Product Overview of Linear Bushings

The flanged Linear Bushings integrates the linear bearing with the support, which is compact in structure and easy to assemble to the mechanism accurately and simply.

Product Feature of Linear Bushings

Linear Bushings, Linear bearing is a linear type motion guiding mechanism matched with linear guide shaft. The steel ball rolls circularly along the track groove formed by the shell and the retainer, and the linear bearing reciprocates linearly relative to the guide shaft.
Through the rolling of steel ball, high-efficiency movement with low friction resistance can be realized.

Dimensional Drawing of Linear Bushings

This product of Linear Bushings is delivered at the initial stage, the color of the packing may be inconsistent with the photo, which shall be subject to the actual product.

The flange part of this product is not heat-treated, and there may be bumps and bruises.

Specifications Overview of Linear Bushings

Counterbored	Linear Bushings Type	Housing	Ball	Retainer	Operating environment temperature	Accessories
		Material	Hardness	Surface Treatment		Material	Material	Material
Opposite Counterbored	E-LBKZ	Equivalent to SUJ2	58HRC～	－	Equivalent to SUJ2	Resin	－20～80℃	Nitrile Rubber
Standard	C-LMK
	E-LBK
	E-LBKM			Electroless Nickel Plating

If there are requirements for rust prevention, give priority to products with surface treatment of electroless nickel plating or those with low temperature hard chromium plating.

Specification Table of Linear Bushings

		Part Number( Type・Inner Diameter・Length
		C-LMK8UU E-LBK8UU

■ Dimension Specification Table of Linear Bushings

Part No.				Outer Diameter. D					Overall Length L			H	T	d	d₁
Type	dr	Tolerance	Length (Ball Retainer)		Single No Surface treatment	Double No Surface treatment	Single With Surface treatment	Double With Surface treatment	Single UU	Double Luu	Torerance
E－LBKZ E－LBK E－LBKM	6	＋0.003 －0.012	UU (Single) LUU (Double)	12	0 －0.015	0 －0.016	0 －0.015	0 －0.015	19	35	±0.3	28	3.5	2.5	4.5
	8			15					24	45		32
	10			19		0 －0.018	0 －0.018	0 －0.018	29	55	±0.6	40	6	4.5	7.5
	12			21	0 －0.018				30	57		42
	13			23					32	61		43
	16			28					37	70		48
	20	＋0.003 －0.013		32	0 －0.021	0 －0.021	0 －0.021	0 －0.021	42	80		54	8	5.5	9
	25			40					59	112		62
	30			45					64	123		74	10	6.6	11
	35	＋0.003 －0.016		52	0 －0.028	0 －0.03	0 －0.025	0 －0.028	70	135		82
E－LBK E－LBKM	40			60					80	151		96	13	9	14
	50			80	0 －0.03	0 －0.032	0 －0.028	0 －0.03	100	192		116

Specification of "E-LBK" corresponds to the spec of "C-LMK". Difference between these 2 type is only Part No.

Part Number			Outer Diameter: D		Total Length: L		H	T	d	d1	t	P.C.D.	W	Lateral misalignment	Number of ball rows	Verticality	Weight (g)	Basic Rated Load
Type	dr	Tolerance		Tolerance		Tolerance												C (Dynamic) N	Co (Static) N
C-LMK_UU	6	+0.003 -0.012	12	0 -0.015	19	±0.6	28	5	3.5	6	3.1	20	22	0.024	4	0.024	18	206	265
	8		15		24		32					24	25				29	265	380
	10		19		29		40	6	4.5	7.5	4.1	29	30				52	372	549
	12		21	0 -0.018	30		42					32	32				57	412	598
	16		28		37		48					38	37		5		104	775	1180
	20	+0.003 -0.013	32	0 -0.021	42		54	8	5.5	9	5.1	43	42	0.03		0.03	145	882	1370
	25		40		59		62					51	50		6		300	980	1570
	30		45		64		74	10	6.6	11	6.1	60	58				375	1570	2740

Usage Method of Linear Bushings

Product Drawings of Linear Bushings	Instructions for use of Linear Bushings
	When the Linear Bushings is under heavy load (unbalanced load), one piece of single liner type is not applicable. It is recommended to use one piece of double liner type or multiple pieces of single liner type.
	Linear Bushings is not suitable for rotating motion in structure. If you rotate forcibly, it may cause damage to the product. Please pay attention during use.
	Linear Bushings, Linear bearing is not suitable for repeated plugging and unplugging.
	When inserting the guide shaft into the linear bearing, please align the center and insert it slowly, otherwise the steel ball will fall off or the retainer will be deformed.

Precautions of Linear Bushings

■ Regular maintenance:
① Before use, please apply grease to the ball row inside the Linear Bushings, linear bearing, and then replenish it in due course. Grease forms an oil film on the surfaces of steel ball and rolling surface (guide shaft·bushing) of linear bearing, which effectively reduces friction and prevents sintering. Grease reduction and aging will greatly affect the life of linear bearing.
② Recommended grease: lithium soap grease.
③ Recommended grease filling interval: Usually every 6 months.
④When the moving distance is long, it is recommended to move once every three months or when the moving distance exceeds 1000km within the time limit, the 1000km shall prevail.
⑤ When the linear bearing is subjected to large moment load (eccentric load), one piece of single liner type is not applicable, so it is recommended to use one piece of double liner type or multiple pieces of single liner type.

■ Dust prevention measures:
If dust or foreign matter enters the inside of the Linear Bushings, linear bearing, it may damage the circulation of steel balls, resulting in unexpected failures. When used in harsh environment, please install dust cover and protection cover, etc.

■ MISUMI linear bearing is recommended to be combined with guide shaft with quenching g6 tolerance.

■ MISUMI linear bearing is recommended to be installed on the holder with H7 tolerance. The linear bearing is in clearance fit with the holder.

Related Products of Linear Bushings

Guide shaft Straight bar type	(Economy series) Linear Bushings Standard type Single liner type	Shaft Collar Slit

Typical Linear Bushings model: SFJ20-75	Typical Linear Bushings model: C-LM8UU	Typical Linear Bushings model: SCS8-10

Part Number

Incomplete part number.
Please use left hand selections to complete a part number.Incomplete part number.
Please use left hand selections to complete a part number.

Loading...Tải…

: 30; 45; 60

Part Number
E-LBKM13LUU SALE

Part Number Price Minimum Order Qty. Volume Discount Days to ShipSố ngày giao hàng Inscribed Circle Dia. dr
(Ø) Overall Length L
(mm) Outer Cylinder Surface Treatment Outer Dia. D
(Ø) Ball Recirculating Type Length Eccentricity
(µm) Basic Load Rating: Dynamic Load (Details)
(N) Basic Load Rating: Static Load
(N) Inscribed Circle Dia. Tolerance (Negative Side)
(mm) Holder Material Style of Mounting Hole

Part Number	Price	Minimum Order Qty.	Volume Discount	Days to ShipSố ngày giao hàng	Inscribed Circle Dia. dr (Ø)	Overall Length L (mm)	Outer Cylinder Surface Treatment	Outer Dia. D (Ø)	Ball Recirculating Type	Length	Eccentricity (µm)	Basic Load Rating: Dynamic Load (Details) (N)	Basic Load Rating: Static Load (N)	Inscribed Circle Dia. Tolerance (Negative Side) (mm)	Holder Material	Style of Mounting Hole
	138,873 VND 118,042 VND	1 Piece(s)	Available	Same day	13	61	[Surface Treatment] Electroless Nickel Plating	23	Double	Double	0.03	813	1570	-0.018	-	Standard Counterbored Hole

138,873 VND

118,042 VND

1 Piece(s)

Available

Same day

[Surface Treatment] Electroless Nickel Plating

Double

0.03

813

1570

-0.018

Standard Counterbored Hole

Loading...Tải…

Basic InformationThông tin cơ bản

Type	Flange	Flange Type	Standard Flange	Style	Standard
Outer Cylinder Material	SUJ2 Equivalent	Lubrication Type	Not Provided	Accuracy	Standard Grade
Motion	Linear	Types	Standard Flange	Flange Shape	Square Flange
Ball Material	SUJ2 Equivalent	Retainer Material	Plastic	Seal	Provided
Greased Filled	Not Provided

Please check the type/dimensions/specifications of the part E-LBKM13LUU in the Square Flanged Linear Bushings, Single / Double / Opposite Counterbored Hole series.Vui lòng kiểm tra kiểu/kích thước/thông số kỹ thuật của phần E-LBKM13LUU trong chuỗi Square Flanged Linear Bushings, Single / Double / Opposite Counterbored Hole.

The specifications and dimensions of some parts may not be fully covered. For exact details, refer toCác thông số kỹ thuật và kích thước của mã sản phẩm có thể không được bao phủ đầy đủ. Để biết chi tiết chính xác, hãy tham khảo manufacturer catalogsdanh mục nhà sản xuất ..

Frequently asked question (FAQ)FAQ

Question:Question: What brand is the linear bearing of FA?: Answer:Answer: The linear bearing of FA is MISUMI brand.
Question:Question: Is there a product stamp on the linear bearing?: Answer:Answer: There is no stamp on the product body, and the product model is on the packaging box.
Question:Question: How is linear bearing maintained regularly?: Answer:Answer: MISUMI recommends that linear bearing is regularly replenished with grease, and it is recommended to do so once every six months. When the moving distance is long, it is recommended to move once every three months or when the moving distance exceeds 1000km within the time limit, the 1000km shall prevail.
Question:Question: Comparison of antirust ability of linear bearings?: Answer:Answer: Antirust ability from strong to weak: No-Electro Nickel Plated → No Surface Treatment.
Standard grade bearing steel is easy to rust, so it is necessary to apply anti-rust oil regularly.
Question:Question: What is the difference between the single liner type and the double liner type of linear bearing of FA?: Answer:Answer: Single liner type is one row of steel balls, and double liner type is two rows of steel balls. Generally, the length of the double liner type is more than twice that of the single liner type, and the contact area of steel balls is longer, the radial sway is smaller, and the rated load is larger.
Question:Question: When the linear bearing and the guide shaft are used together, some are closely matched, but some have relatively large clearance. Does it affect the use?: Answer:Answer: The linear bearing and the guide shaft are in point contact and rolling fit through the circulating steel ball structure. Because of point contact and non-interference fit, it is normal to have clearance between the shaft and the bearing, which will not affect the use. The use of this structure greatly reduces the friction resistance and prolongs the service life of the workpiece.
Question:Question: How to deal with oil leakage in the received linear bearing?: Answer:Answer: Linear bearing is coated with anti-rust oil (except for MX grease device) when leaving the factory, which has little influence on grease. It is recommended to clean it before use and apply grease after drying.
Question:Question: Can the linear bearing rotate?: Answer:Answer: The linear bearing is not suitable for rotating motion in structure. If it is forcibly rotated, it may cause damage to the product. If rotating motion is required, please give priority to linear type rotating bushings.

Check other FAQ (5 items) HideĐóng.

Products like this...

Part Number
E-LBK12UU
E-LBK13LUU
E-LBK13UU
E-LBKM13UU
E-LBKM16LUU
E-LBKM16UU

Standard Unit Price	Minimum order quantity	Volume Discount	Days to ShipSố ngày giao hàng	Inscribed Circle Dia. dr (Ø)	Overall Length L (mm)	Outer Cylinder Surface Treatment	Outer Dia. D (Ø)	Ball Recirculating Type	Length	Eccentricity (µm)	Basic Load Rating: Dynamic Load (Details) (N)	Basic Load Rating: Static Load (N)	Inscribed Circle Dia. Tolerance (Negative Side) (mm)	Holder Material	Style of Mounting Hole
53,780 VND	1 Piece(s)	Available	Same day	12	30	No Surface Treatment	21	Single	Single	24	412	598	-0.018	-	Standard Counterbored Hole
118,691 VND	1 Piece(s)	Available	Same day	13	61	No Surface Treatment	23	Double	Double	0.03	813	1570	-0.018	-	Standard Counterbored Hole
75,998 VND	1 Piece(s)	Available	Same day	13	32	No Surface Treatment	23	Single	Single	0.024	510	784	-0.018	Standard	Standard Counterbored Hole
87,640 VND	1 Piece(s)	Available	Same day	13	32	[Surface Treatment] Electroless Nickel Plating	23	Single	Single	0.024	510	784	-0.018	Standard	Standard Counterbored Hole
148,190 VND	1 Piece(s)	Available	Same day	16	70	[Surface Treatment] Electroless Nickel Plating	28	Double	Double	0.03	1230	2350	-0.018	-	Standard Counterbored Hole
92,295 VND	1 Piece(s)	Available	Same day	16	37	[Surface Treatment] Electroless Nickel Plating	28	Single	Single	0.024	775	1180	-0.018	Standard	Standard Counterbored Hole

Top of the page

About MISUMIVề Misumi

About this WebsiteVề trang Web này

Useful ToolsCác công cụ hữu ích

Customer ServiceDịch vụ chăm sóc khách hàng

MISUMI Contact Monday to Saturday: 8:00 am - 5:00 pm Order cut off time is 5:00 pm Thứ 2 đến Thứ 7: 8 giờ sáng đến 5 giờ chiều Hạn chót đặt hàng là 5 giờ chiều

Tel:Số điện thoại:0222-361-1555
Fax:Số Fax:0222-361-2555
InquiryYêu cầu

MISUMI APP

Install MISUMI APP

MISUMI Vietnam Company Limited, Legal Representative: Tomohiro Watanabe,
phone: 0222-361-1555, e-mail: cs@misumi.com.vn, Enterprise Code: 0107514576,
Date of Issuance: 22 July 2016, Place of Issuance: Bac Ninh, Business Certificate No. 6573041568-KD dated 27 September 2016 issued by the People's Committee of Bac Ninh

Công ty TNHH MISUMI Việt Nam, Đại diện theo pháp luật: Tomohiro Watanabe,
Điện thoại: 0222-361-1555, e-mail: cs@misumi.com.vn, Mã số doanh nghiệp: 0107514576,
ngày cấp 22/7/2016, nơi cấp: Bắc Ninh, Giấy phép kinh doanh số: 6573041568-KD ngày cấp 27/9/2016 bởi UBND tỉnh Bắc Ninh

Search by Category / Brand Tìm theo danh mục, nhãn hiệu

Search by Category Tìm theo danh mục

How can we improve?

ConfigureTạo

Specification/DimensionsĐặc điểm kỹ thuật / Kích thướcĐặc điểm kỹ thuật / Kích thước

Holder Material

type

Inscribed Circle Dia. dr(Ø)

Overall Length L(mm)

Outer Cylinder Surface Treatment

Outer Dia. D(Ø)

Ball Recirculating Type

Length

Eccentricity(µm)

Style of Mounting Hole

CADCAD